tas_a114_bms_mia
Safe to driveTesla · TAS system
Air Suspension — BMS Communication Lost
What it means
The Tesla Air Suspension controller is not receiving expected messages from the Battery Management System. On Cybertruck, the air suspension tank is also used to pressurize the battery pack enclosure, so that specific function may be limited — the suspension itself generally keeps working.
Symptoms
- No customer-facing message in most cases
- Silent alert on the center display
- Ride height and suspension behavior usually normal
- Battery pack pressurization function may be limited (Cybertruck)
Likely causes (by probability)
- 1.CAN communication fault between the suspension ECU and the BMSMedium
- 2.BMS temporarily offline (check for other MIA alerts)Medium
- 3.Software glitch cleared by a sleep cycle or updateLow
What you can check yourself
- 01Do a full sleep cycle and see if the alert clears
- 02Confirm the suspension still raises and lowers normally
- 03Install pending software updates
- 04Check for other modules reporting BMS MIA at the same time
EV systems involved in tas_a114_bms_mia
Body domain controllers
Distributed controllers around the car (front, left, right, doors, seats, charge port) that run lights, latches, wipers, windows and actuators, and report state back over the vehicle network. A mismatch between what a latch says and what the network sees is a classic body-domain fault.
High-voltage battery pack
The traction battery — hundreds of lithium-ion cells grouped into modules, plus the sense harness that reports every cell group's voltage and temperature. It is the single most expensive component in the car, and most battery-related alerts originate from measurements taken here.
Battery management system (BMS)
The pack's dedicated computer. It balances cells, estimates state of charge and health, controls the main contactors, watches isolation, and decides when the pack must limit power or refuse to operate. Nearly every "the battery says no" behavior traces back to the BMS.
Vehicle network (CAN / gateway)
Multiple CAN buses link every controller; the gateway routes messages between them and to diagnostics. "MIA" (missing in action) alerts almost always mean a node stopped sending on its bus — the cause can be the node itself, its wiring, or its power supply.
Deep dive: what owners should know
The air suspension module would seem to have little to do with the battery beyond consuming its power, which is exactly why TAS_A114 is so instructive: when even the suspension controller is logging "BMS missing," the diagnostic picture snaps into focus. This is not a suspension problem, and treating it as one sends you down an expensive dead end. The A114 code means the suspension module woke up, reached for its routine BMS messages — state of charge, available power, thermal status — and found silence. The suspension uses that data for ride-height strategy tied to range and thermal conditions, data every module on the network consumes in its own way. Its complaint joins the chorus every other module raises in the same moment, and the full alert list from that moment — often a dozen MIA codes logged within seconds of each other — is the single most valuable screenshot an owner can bring to diagnosis, because it proves the event was a network silence, not a module failure. The cause families behind that silence are the ones the whole MIA family shares. A BMS reboot silences the network for seconds and produces a one-time storm that never recurs; this is the most common origin and the only one that self-resolves. A CAN backbone fault — corrosion, a loose pin, damaged wiring — makes the silence intermittent and recurring, usually weather-sensitive, and tends to collect neighboring communication codes alongside the MIA family. A genuinely failing BMS or its power supply converts intermittent silence to permanent silence, and the car's behavior degrades from alert-heavy to non-functional as the condition hardens. The free triage is unchanged: sleep the car fully, wake it, drive. Alerts that never return were a reboot. Alerts that return deserve a network professional, promptly.
Severity
Low urgency if the suspension works normally. Mention it at your next service visit, especially if other communication alerts appear alongside it.
Estimated repair cost
Dealer / service center
— – —
Usually a communication or software fix; varies by warranty status — get a quote from Tesla Service.
DIY
Not DIY-safe — professional repair recommended.
Estimated ranges based on owner reports. Actual pricing varies by model, year, region and warranty status.
What to read next
Related fault codes
Other alerts from the same failure family — useful for cross-checking symptoms.