All codes

bms_a107_sw_stack_voltage_mia

Do not drive

Tesla · BMS system

Battery Management System — Stack Voltage Measurement Lost

What it means

The BMS has lost the ability to measure the voltage of one or more stacks inside the pack. Flying blind on stack voltage is not acceptable for charging — the BMS needs those numbers to charge safely — so charging is disabled until the measurements return.

Symptoms

  • "Unable to charge — Service required" message
  • Charging disabled
  • Single chime with a warning icon
  • Driving may still be possible

Likely causes (by probability)

  1. 1.Monitoring board or sense-lead fault on the affected stackMedium
  2. 2.Connector problem in the voltage sense pathMedium
  3. 3.Wiring damage inside the packLow
  4. 4.BMS measurement circuit faultLow

What you can check yourself

  • 01Try a full sleep cycle; if the measurement comes back, still report it — intermittent sense faults tend to return.
  • 02Check for companion voltage-sensing alerts to help service localize the fault.
  • 03Do not attempt internal pack inspection — sense leads connect directly to high-voltage cell groups.
  • 04Plan around reduced mobility: charging is off the table until fixed.

EV systems involved in bms_a107_sw_stack_voltage_mia

Battery management system (BMS)

The pack's dedicated computer. It balances cells, estimates state of charge and health, controls the main contactors, watches isolation, and decides when the pack must limit power or refuse to operate. Nearly every "the battery says no" behavior traces back to the BMS.

Charging system

The charge port, onboard charger (AC), fast-charge controller (DC/CHAdeMO/GB-T), and all the communication protocols that negotiate current between the car and the charging station. Failures split cleanly into power problems and communication problems.

High-voltage battery pack

The traction battery — hundreds of lithium-ion cells grouped into modules, plus the sense harness that reports every cell group's voltage and temperature. It is the single most expensive component in the car, and most battery-related alerts originate from measurements taken here.

Vehicle network (CAN / gateway)

Multiple CAN buses link every controller; the gateway routes messages between them and to diagnostics. "MIA" (missing in action) alerts almost always mean a node stopped sending on its bus — the cause can be the node itself, its wiring, or its power supply.

Deep dive: what owners should know

The stack voltage is the single most important measurement the BMS makes — the total voltage of the entire series string of cells, the number everything else is sanity-checked against. BMS_A107 means the BMS has lost that measurement: the message carrying stack voltage is missing, stale, or implausible, and the system is now flying with one of its primary instruments dark. The immediate consequence is conservative behavior everywhere, because every power and charging decision the BMS makes is gated on knowing the pack voltage within a tight tolerance. The cause ladder starts where these codes usually start: the measurement path itself. Stack voltage is derived through the voltage sense harness and the pack's monitoring hardware, so a connector with high resistance, a corroded pin, or a fault in the sensing circuit produces exactly this signature. The second rung is the monitoring boards — the distributed BMBs that measure cell groups and report upward — where one misbehaving board corrupts the aggregated value. The third rung, and the one owners least want but should verify early, is the BMS side: its input channel or reference supply failing to read a healthy signal. Because the sense harness is the classic failure point, the related isolation and harness codes that accompany this one are diagnostically valuable — a cluster of voltage-sensing and isolation codes points hard at harness and connector health rather than cell health. If you run an OBD tool, the comparison between individual brick voltages summing correctly while the reported stack voltage reads zero or frozen is the smoking-gun screenshot. This is not a code to clear and forget; a BMS uncertain of pack voltage will eventually refuse to energize the car at all.

Severity

Do not drive

Charging is disabled, so treat remaining range as all you have. Book service promptly.

Estimated repair cost

Dealer / service center

— – —

Covered under battery warranty in many cases; out-of-warranty cost varies — get a quote from Tesla Service.

DIY

Not DIY-safe — professional repair recommended.

Estimated ranges based on owner reports. Actual pricing varies by model, year, region and warranty status.

Content pending community verification. This entry is based on public owner reports and general repair knowledge. Exact part numbers, prices and procedures vary by model year — confirm with your service documentation before acting. Not affiliated with any vehicle manufacturer.

What to read next

Related fault codes

Other alerts from the same failure family — useful for cross-checking symptoms.

Featured on NewTool.site