bms_f033_sw_crash
Do not driveTesla · BMS system
Battery Management System: Crash Event Detected (Pyro Fuse Blown)
What it means
The BMS saw the battery pack lose power to the contactors while they were closed, and concluded the pyro fuse — a one-shot explosive disconnect designed to fire in a crash — has blown. This is the battery doing exactly what it is designed to do after an impact: cut all high-voltage power instantly. The pyro fuse does not reset; it must be replaced.
Symptoms
- "Service required / Pull over safely" message
- Complete loss of high-voltage power — no driving or charging
- Appears after a collision, or after a hard impact to the underbody
Likely causes (by probability)
- 1.Actual collision or significant impact triggered the pyro fuse as designedHigh
- 2.Pyro fuse fired erroneously due to a control circuit faultLow
- 3.Contactor power supply wiring failure mimicking a blown fuseLow
What you can check yourself
- 01Do not attempt to restart or drive the car — the high-voltage system is intentionally disabled
- 02If a crash occurred, tell the tow operator it is an EV with a triggered battery disconnect
- 03Have the car inspected even if the impact seemed minor — underbody hits can trigger this
- 04Never attempt to replace or bypass the pyro fuse yourself; it is an explosive device inside the battery pack
EV systems involved in bms_f033_sw_crash
Battery management system (BMS)
The pack's dedicated computer. It balances cells, estimates state of charge and health, controls the main contactors, watches isolation, and decides when the pack must limit power or refuse to operate. Nearly every "the battery says no" behavior traces back to the BMS.
Charging system
The charge port, onboard charger (AC), fast-charge controller (DC/CHAdeMO/GB-T), and all the communication protocols that negotiate current between the car and the charging station. Failures split cleanly into power problems and communication problems.
High-voltage battery pack
The traction battery — hundreds of lithium-ion cells grouped into modules, plus the sense harness that reports every cell group's voltage and temperature. It is the single most expensive component in the car, and most battery-related alerts originate from measurements taken here.
High-voltage distribution & safety
Contactors (big relays that connect the pack to the car), the pyrofuse (a one-shot crash disconnect), precharge circuitry, and the isolation monitor that constantly checks high voltage is not leaking to the chassis. Faults here are treated as safety-critical.
Deep dive: what owners should know
The pyrofuse is the battery pack's one-shot bodyguard: a small explosive-driven disconnect that fires in a detected crash, physically severing the high-voltage connection faster than any relay could open under load. It does its job once and then it is done — a used pyrofuse is a permanent change to the car's hardware state, and BMS_F033 is the system confirming that this exact event happened. The BMS knows because it commanded or detected the pyro activation in response to a crash signature from the restraint controllers, and after the event it can see the pyro's status circuit reading "fired." First, the context that matters most: if this code appeared after an actual collision, the sequence worked exactly as designed. The high-voltage system disconnected to protect occupants and responders, the car did its job, and this code is the receipt. The repair conversation in that case is body-shop territory, and the pyrofuse is replaced as part of collision repair — not a standalone maintenance item. Second, and rarer, is the code appearing without any collision: pyro status circuits can misreport, harness damage can mimic a fired state, and in these cases the code arrives with no corresponding event in anyone's memory. That version needs professional diagnosis quickly, because the BMS now believes it cannot rely on its crash disconnect — a car that thinks its bodyguard already left the building behaves conservatively, and should. Either way, there is no DIY angle on this one: pyrofuse replacement involves the pack, the high-voltage system, and post-repair isolation verification. Document everything, involve insurance if a collision triggered it, and let qualified hands do the work.
Severity
The car will not move and must be towed. The pyro fuse and any crash damage must be inspected and replaced by Tesla Service.
Estimated repair cost
Dealer / service center
— – —
Pyro fuse replacement plus mandatory pack inspection; collision-related work is often handled through insurance — get a quote from Tesla Service.
DIY
Not DIY-safe — professional repair recommended.
Estimated ranges based on owner reports. Actual pricing varies by model, year, region and warranty status.
What to read next
Related fault codes
Other alerts from the same failure family — useful for cross-checking symptoms.
- bms_w033_sw_crashBattery Management System — Crash Detected (Battery Pyrofuse Blown)
- bms_f179_replacesmartfuselimpBattery Management System: Pyro Fuse Past Service Life — Replacement Required
- bms_u032_replacesmartfuseneededBattery Management System — Battery Pyrofuse Nearing End of Life
- rcm2_a202_driverfsabopenRestraint Controller — Driver Far-Side Airbag Circuit Open