All codes

bms_a066

Safe to drive

Tesla · BMS system

Battery Management System — Charge Port / Charging Communication Fault

What it means

The BMS reports it cannot communicate properly with the charging equipment or the charge port electronics. The car and the charger are not agreeing on how to charge.

Symptoms

  • Charging stops mid-session or never starts
  • Charge port light flashing red or amber
  • Works on some chargers but not others

Likely causes (by probability)

  1. 1.Dirty or damaged charge port pinsHigh
  2. 2.Incompatible or faulty charging station / wall connectorMedium
  3. 3.Charge port ECU failureMedium
  4. 4.Wiring fault between port and BMSLow

What you can check yourself

  • 01Inspect the charge port for debris, corrosion or bent pins (flashlight only — power off first).
  • 02Try a different charger and a different cable to isolate the problem.
  • 03Fully power off the car and retry — charge-port ECU glitches often clear.
  • 04Check for recent software updates; charging logic bugs are occasionally fixed OTA.

EV systems involved in bms_a066

Battery management system (BMS)

The pack's dedicated computer. It balances cells, estimates state of charge and health, controls the main contactors, watches isolation, and decides when the pack must limit power or refuse to operate. Nearly every "the battery says no" behavior traces back to the BMS.

Charging system

The charge port, onboard charger (AC), fast-charge controller (DC/CHAdeMO/GB-T), and all the communication protocols that negotiate current between the car and the charging station. Failures split cleanly into power problems and communication problems.

Body domain controllers

Distributed controllers around the car (front, left, right, doors, seats, charge port) that run lights, latches, wipers, windows and actuators, and report state back over the vehicle network. A mismatch between what a latch says and what the network sees is a classic body-domain fault.

Vehicle network (CAN / gateway)

Multiple CAN buses link every controller; the gateway routes messages between them and to diagnostics. "MIA" (missing in action) alerts almost always mean a node stopped sending on its bus — the cause can be the node itself, its wiring, or its power supply.

Deep dive: what owners should know

BMS_A066 occupies the awkward middle ground where the car works perfectly except for the one thing you bought an EV to do: charge it. The BMS is the conductor of the charging orchestra — it talks to the charge port, negotiates with the wall connector or Supercharger, sets current limits, and watches every cell while energy flows. This code means that conversation is breaking down somewhere between the port and the battery. The useful diagnostic insight is that charging communication fails in two very different places. The first is physical: dirty, corroded or mechanically damaged pins in the charge port, a latch that cannot confirm the cable is seated, water in the connector. These produce the version of the fault that comes and goes, works on one charger but not another, or improves after cleaning. The second is electronic: the charge port ECU, the pilot signal wiring, or the BMS-side charge logic itself. That version tends to be consistent across all chargers and stubborn across reboots. Owners can split the difference quickly with two tests: try a completely different charging location (ideally a Supercharger versus home AC), and inspect the port with a flashlight for debris, discoloration or bent pins. If AC charging fails but DC Supercharging works, suspect the onboard charger side and the port's AC pins; if everything fails, suspect the port electronics or wiring. The good news is this is a "safe" severity in every sense — driving is completely unaffected — and the worst case, a charge port assembly, is a well-documented repair that many owners do themselves with basic tools.

Severity

Safe to drive

Driving is unaffected; charging convenience is the issue.

Estimated repair cost

Dealer / service center

$200 – $1,200

Charge port replacement is the typical worst case.

DIY

$0 – $400

Cleaning costs nothing; a used/new charge port is a bolt-on part for experienced DIYers.

Estimated ranges based on owner reports. Actual pricing varies by model, year, region and warranty status.

Content pending community verification. This entry is based on public owner reports and general repair knowledge. Exact part numbers, prices and procedures vary by model year — confirm with your service documentation before acting. Not affiliated with any vehicle manufacturer.

What to read next

Related fault codes

Other alerts from the same failure family — useful for cross-checking symptoms.

Featured on NewTool.site