hvbatt_a120_externalisolation
Do not driveTesla · HVBATT system
High-Voltage Battery — Low Isolation Detected Outside the Pack
What it means
With the main contactors closed, the BMS measured the electrical isolation between the high-voltage system and the car body and found it too low. Isolation is what keeps the pack's hundreds of volts safely away from the chassis — a low reading means something in the high-voltage system is leaking toward ground.
Symptoms
- "Vehicle may not restart — Service required" message
- Car may refuse to charge or drive
- Warning chime when the alert sets
- Often follows water exposure, flooding, or high-pressure washing
Likely causes (by probability)
- 1.Moisture or contamination inside a high-voltage component (drive unit, heater, A/C compressor, cabling)High
- 2.Damaged or chafed orange high-voltage cablingMedium
- 3.Coolant intrusion into a high-voltage componentLow
What you can check yourself
- 01Think back to water exposure — deep puddles, floods, or underbody sprays are prime suspects
- 02Check for companion isolation alerts (a122, a123) that show whether it is getting worse
- 03Do a full sleep cycle and see if the reading recovers as things dry out
- 04Never touch, bridge, or probe orange high-voltage components or the isolation system — this is strictly Tesla Service territory
EV systems involved in hvbatt_a120_externalisolation
High-voltage battery pack
The traction battery — hundreds of lithium-ion cells grouped into modules, plus the sense harness that reports every cell group's voltage and temperature. It is the single most expensive component in the car, and most battery-related alerts originate from measurements taken here.
Cabin HVAC
The heat pump / A/C compressor, cabin blower and valves that move heat between battery, motors and cabin. In a heat-pump car, cabin comfort and battery conditioning share one refrigerant loop, so HVAC faults often follow thermal-system faults.
Battery management system (BMS)
The pack's dedicated computer. It balances cells, estimates state of charge and health, controls the main contactors, watches isolation, and decides when the pack must limit power or refuse to operate. Nearly every "the battery says no" behavior traces back to the BMS.
High-voltage distribution & safety
Contactors (big relays that connect the pack to the car), the pyrofuse (a one-shot crash disconnect), precharge circuitry, and the isolation monitor that constantly checks high voltage is not leaking to the chassis. Faults here are treated as safety-critical.
Deep dive: what owners should know
Isolation is the electrical moat around the high-voltage castle, and HVBATT_A120 reports that the moat has been breached somewhere outside the battery pack itself. The distinction this code encodes — external rather than internal isolation loss — is the single most useful bit of information in it, because it redirects the search away from the pack (expensive, sealed, warranty-heavy) and toward the web of high-voltage components the pack feeds: junction boxes, charging hardware, drive units, heater, compressor, and the orange cabling that strings them together. The isolation monitor measures resistance between the high-voltage system and chassis continuously, and when that resistance drops below threshold, the system must assume the worst about where current might flow. Causes in the external category are dominated by three suspects. Water ingress into connectors and junction boxes after floods, deep puddles, or aggressive pressure-washing is the runaway leader, and it has the classic moisture signature: appearing after wet events, worsening with humidity, sometimes clearing as things dry. Physical cable damage is second — rodents, debris strikes, chafing at mounting points — and is usually visible to a careful underbody inspection, though touching damaged orange cable is never part of that inspection. Component failure is third: a heater element or compressor developing a chassis leak as it ages. The owner playbook mirrors BMS-side isolation faults with one difference worth noting: because the pack is exonerated by the code itself, warranty conversations about pack hardware should not even start here — the search is outside the battery, and saying so at the service counter saves everyone time. Park it, book it, and let it dry somewhere warm if water is suspected.
Severity
Low isolation is a genuine electrical safety issue. Do not keep driving on it — schedule service promptly and mention any water exposure.
Estimated repair cost
Dealer / service center
— – —
Covered under battery warranty in many cases; out-of-warranty cost varies — get a quote from Tesla Service.
DIY
Not DIY-safe — professional repair recommended.
Estimated ranges based on owner reports. Actual pricing varies by model, year, region and warranty status.
What to read next
Related fault codes
Other alerts from the same failure family — useful for cross-checking symptoms.
- bms_f018Battery Management System — Insulation / Isolation Monitoring Fault
- hvbatt_a122_isolationdegradationHigh-Voltage Battery — Isolation Degrading (Early Warning)
- bms_a142_sw_isolation_degradationBattery Management System — Isolation Degraded (Warning Level)
- bms_w027_sw_drive_iso_repeatedBattery Management System — Repeated Loss of High-Voltage Isolation While Driving