bms_a166_sw_pack_full_weld
Do not driveTesla · BMS system
Battery Management System — Both Pack Contactors Welded
What it means
The BMS self-test found that both main pack contactors are welded shut. The pack can no longer disconnect itself from the car at all — its primary safety disconnect is fully defeated. The car blocks driving, charging, and low-voltage support because operating without any way to cut high voltage is not acceptable.
Symptoms
- Car will not drive or charge
- Silent center-display alert
- Detected at startup self-test
- Car may appear normal on screens but refuse to operate
Likely causes (by probability)
- 1.Severe overcurrent event (short circuit downstream) fusing both contactorsMedium
- 2.Both contactors at end of life (high-mileage, many cycles)Low
- 3.Pre-charge failure causing repeated under-load closuresMedium
- 4.Faulty weld-detection circuit reporting a false positiveLow
What you can check yourself
- 01Do not attempt any contactor or pack work — both the voltage and the stored energy here are lethal.
- 02Do not keep cycling power hoping it clears; welded contacts do not unweld themselves.
- 03Note any events preceding the alert: hard faults, failed starts, prior HV warnings.
- 04Arrange a tow to service — flatbed, per Tesla's transport guidance.
EV systems involved in bms_a166_sw_pack_full_weld
Battery management system (BMS)
The pack's dedicated computer. It balances cells, estimates state of charge and health, controls the main contactors, watches isolation, and decides when the pack must limit power or refuse to operate. Nearly every "the battery says no" behavior traces back to the BMS.
Charging system
The charge port, onboard charger (AC), fast-charge controller (DC/CHAdeMO/GB-T), and all the communication protocols that negotiate current between the car and the charging station. Failures split cleanly into power problems and communication problems.
High-voltage battery pack
The traction battery — hundreds of lithium-ion cells grouped into modules, plus the sense harness that reports every cell group's voltage and temperature. It is the single most expensive component in the car, and most battery-related alerts originate from measurements taken here.
High-voltage distribution & safety
Contactors (big relays that connect the pack to the car), the pyrofuse (a one-shot crash disconnect), precharge circuitry, and the isolation monitor that constantly checks high voltage is not leaking to the chassis. Faults here are treated as safety-critical.
Deep dive: what owners should know
A welded contactor sounds abstract until you understand what contactors do all day: they are the high-voltage gates between the battery and everything else, opening and closing on command, carrying hundreds of amps, expected to fail-safe in every scenario engineers can imagine. A welded contactor fails that expectation in the most specific way — the contacts have fused shut, so the gate cannot open. BMS_A166 is the BMS confirming that both main contactors have welded, and the implications are immediate and serious: the battery cannot disconnect from the high-voltage bus, which means the car cannot make itself electrically safe, which means this code is do-not-drive, do-not-charge, call-for-a-tow territory without negotiation. The physics of welding is straightforward: contacts carrying heavy current can arc as they open, and the arc spot-welds the contact surfaces together. Heavy users see this — tow vehicles, track cars, anything that lives at high sustained current — and aging contactors see it as their contact material erodes and arcing worsens. The BMS detects the state directly: it commands the contactors open, measures, and finds the bus still energized. Its siblings in the weld family — partial weld codes for one contactor, fast-charge-side weld codes — describe the same failure with different gates stuck, and the diagnostic logic is identical. Replacement means pack-side or junction-box work on a system that currently cannot be made safe by command, which is precisely why tow-and-service is the only correct answer. There is no owner-level repair and no meaningful owner-level diagnosis beyond recognizing the severity and acting on it.
Severity
This is a hard stop. The pack cannot disconnect, so the car stays parked until a technician replaces the contactors.
Estimated repair cost
Dealer / service center
— – —
Covered under battery warranty in many cases; out-of-warranty cost varies — get a quote from Tesla Service.
DIY
Not DIY-safe — professional repair recommended.
Estimated ranges based on owner reports. Actual pricing varies by model, year, region and warranty status.
What to read next
Related fault codes
Other alerts from the same failure family — useful for cross-checking symptoms.
- bms_a165_sw_pack_partial_weldBattery Management System — One Pack Contactor Welded
- bms_a168_sw_fc_full_weldBattery Management System — Both Fast-Charge Contactors Welded
- bms_w152_sw_pos_contactor_weldedBattery Management System — Positive Contactor Welded Shut
- bms_w153_sw_neg_contactor_weldedBattery Management System — Negative Contactor Welded Shut