bms_u011_fast_charger_problem
Drive with cautionTesla · BMS system
Battery Management System — DC Fast Charging / Supercharging Blocked
What it means
The battery management system has detected a problem that prevents DC fast charging, so Supercharging (and other DC fast charging) won't start or will stop. Regular AC charging at home or a Level 2 station is usually unaffected, and the car still drives normally.
Symptoms
- Supercharging or DC fast charging fails to start or stops early
- Message telling you to disconnect and retry
- AC (Level 2 / home) charging still works
- No effect on normal driving
Likely causes (by probability)
- 1.A problem with the specific Supercharger stall or cable (not your car)High
- 2.Charge port, latch, or inlet communication fault on the carMedium
- 3.Fast-charge contactor or precharge circuit issue inside the battery packMedium
- 4.Software glitch cleared by a reboot or updateLow
What you can check yourself
- 01Unplug, wait a moment, and retry — then move to a different stall or a different station entirely.
- 02Confirm AC charging still works at home or a Level 2 station; that tells you the pack itself is probably fine.
- 03Reboot the car (hold both steering-wheel scroll wheels) and check for pending software updates.
- 04If it fails at every DC station, pull the alert log with Scan My Tesla and schedule service.
EV systems involved in bms_u011_fast_charger_problem
Battery management system (BMS)
The pack's dedicated computer. It balances cells, estimates state of charge and health, controls the main contactors, watches isolation, and decides when the pack must limit power or refuse to operate. Nearly every "the battery says no" behavior traces back to the BMS.
Steering system
Electric power steering rack, torque and angle sensors. Assist faults preserve manual control (the wheel stays mechanically connected) but every assist system disengages as a precaution.
High-voltage battery pack
The traction battery — hundreds of lithium-ion cells grouped into modules, plus the sense harness that reports every cell group's voltage and temperature. It is the single most expensive component in the car, and most battery-related alerts originate from measurements taken here.
High-voltage distribution & safety
Contactors (big relays that connect the pack to the car), the pyrofuse (a one-shot crash disconnect), precharge circuitry, and the isolation monitor that constantly checks high voltage is not leaking to the chassis. Faults here are treated as safety-critical.
Deep dive: what owners should know
Supercharging is the feature that sold a generation of drivers on EVs, and BMS_U011 is the code that takes it away. The "u" prefix flags this as a status alert rather than a component failure: the BMS has determined it cannot authorize DC fast charging, and it wants the condition understood and resolved. The session you attempt will either refuse to start or abort early, while AC charging at home typically continues to work — that split behavior is itself the most important diagnostic clue in the whole code, because AC and DC charging share the battery and the BMS but diverge at the fast-charge path: the dedicated fast-charge contactors, the DC charge port pins, the communication link to the charging station, and the thermal state fast charging demands. The refusal triggers organize into four families. Thermal is the most common: a battery outside its fast-charging temperature window — too cold without preconditioning, too hot after hard use — gets a temporary refusal that resolves with time and conditioning; this is the family most owners meet, and it explains why the alert clusters around winter mornings and summer road-trip arrivals. Isolation and safety come second: any open isolation or safety-related flag suspends fast charging until cleared, because pumping 250 kilowatts through a system with an unresolved safety question is not a negotiation. Cell-condition limits come third: significant imbalance or a weak cell group caps the charge rate the BMS will permit, and when the cap falls below what the station requires, the session refuses to begin. Communication with the station rounds out the list: handshake failures that mimic hardware problems but trace to the station side or the protocol link. The pattern-matching is straightforward: winter arrival refusals are thermal, always-the-same-station refusals are communication, everything-refusals with other BMS codes present are the BMS protecting the pack.
Severity
You can keep driving and AC-charging, but don't plan a road trip until this is sorted. If it happens at multiple stations, book a service visit.
Estimated repair cost
Dealer / service center
— – —
If the fault is in the car (not the charging station), it is often covered under the battery warranty; out-of-warranty cost varies — get a quote from Tesla Service.
DIY
Not DIY-safe — professional repair recommended.
Estimated ranges based on owner reports. Actual pricing varies by model, year, region and warranty status.
What to read next
Related fault codes
Other alerts from the same failure family — useful for cross-checking symptoms.
- bms_u020_cannot_precharge_fcBattery Management System — Cannot Pre-Charge for DC Fast Charging
- fc_a132_ca_bmsmiaFast Charge Controller — CHAdeMO Blocked, BMS Not Responding
- bms_a152_isolation_in_dc_chargeBattery Management System — Low Isolation Detected During DC Charging
- bms_f096_sw_fast_charger_miaBattery Management System: Fast Charger Communication Lost